CAMBRIDGE SOUNDWORKS P500 INSTALL
CAMBRIDGE SOUNDWORKS P500 MANUAL

Adjust the equalizer frequency and equalizer level controls to your preference. 6 60 +6 equalizer level equalizer frequency 2. Adjusting For Best Performance We recommend you adjust the Control Module according to the following sequence: 20 1. Then insert the AC plug into an AC outlet.Д 40 recheck your connections. Insert the subwoofer enclosureвЂ™s power cable into the receptacle on the subwoofer enclosureвЂ™s input panel. Turn the Control ModuleвЂ™s power switch to AUTO. Then insert the POWER 120VAC 7.0A 00000000 INTERFAC E JACKS adapterвЂ™s output plug into the Control ModuleвЂ™s 12V AC input jack. Power Connections First, insert the AC plug of the Control ModuleвЂ™s power Powered Subwoofer supply adapter into an AC outlet. This mark- connect the Interface Cable from the Control Module ing may be a ridge in the insulation, different colored to the Subwoofer Enclosure.ДЇINAL SETUP interface cable. To insure you connect the wires properly (positive to Connect to the Subwoofer Enclosure: Once the positive, negative to negative), note which of each input connections are made to the Control Module, speaker wireвЂ™s two conductors is вЂњmarkedвЂќ. Tighten each set screw to hold the wires in place. SPEAKER OUTPUTS COAX MAIN RIGHT OPTICAL We provide a Speaker Wire Connector with two short Red Band MAIN LEFT lengths of speaker wire already connected to it. Speaker Level Connection TO FRONT LEFT & RIGHT SPEAKERS If your receiver does not have a line-level audio signal output or if you wish to bypass this output, you need to connect the speaker level inputs of the Control Module DIGITAL INPUTS to your receiverвЂ™s speaker outputs. MAIN LEFT CENTER SUB OUT About your audio components: You can connect the REAR RIGHT Control Module to a receiver, an integrated amplifier, a SIGNAL CABLE WITH RCA PLUGS REAR RIGHT preamplifier/power amplifier combination or other This jack is usually labeled 'SUB OUT,' but it may say 'SUBWOOFER' or 'LFE OUTPUT'.

The spikes penetrate a carpet and carpet pad and transfer the weight of the speaker directly to the floor surface.Д¬ONNECTIONS RECEIVER After you have positioned the subwoofer enclosure, DIGITAL INPUTS to connect the Control Module to your audio SPEAKER OUTPUTS COAX MAIN RIGHT OPTICAL components. Installing and adjusting the four carpet spikes can level the speaker and improve its stability on thick carpeting.

INSTALLING CARPET SPIKES Improving Stability With Carpet Spikes Back The powered subwoofer has four soft feet for level, stable orientation on any flat surface and tightly woven carpets. Corner placement also provides the most consistent output from deep bass to upper bass. Some Advantages Of Corner Placement: Placing a subwoofer in or near the corner of a room increases its maximum output. The output increases the closer the subwoofer is placed to the intersection of walls and floors (see diagrams). Its location in the room affects its output. PLACEMENT The subwoofer enclosure should be placed on the floor. Use an audio signal cable with single RCA other jack only when you to connect a second Newton plugs on each end. Main Outputs: Connect the SUB OUT jack from a receiver, integrat- Connect one of these two jacks to the subwoofer ed amplifier, preamplifier, or surround decoder to this enclosure using the supplied Interface Cable. volume: speakers can produce.Д¬ONTROL MODULE INPUTS AND OUTPUTS 6. woofer should not produce any bass your main 4. ItвЂ™s easiest to adjust when percussion is playing to blend well with your main speakers. The affect this control has can be notesвЂќ, the upper end of its range should be tailored subtle. low-pass: Even though a subwoofer only produces вЂњbass for вЂњbest soundвЂќ). OPERATING CONTROLS Adjust it for maximum output in this narrow range (not 1.

Return the subwoofer to the store or merchant where you 2 made the purchase or call Cambridge SoundWorks at 1-800 FOR-HIFI (1-80) for assistance.

CAMBRIDGE SOUNDWORKS P500 INSTALL

If there is any, do not install or use the system. Control module power supply adapter INSPECTING FOR DAMAGE Examine each part carefully for shipping damage. FOLLOW INSTRUCTIONS вЂ“ All operating and use instructions should be followed.Д¬ONTENTS 1 1. RETAIN INSTRUCTIONS вЂ“ The safety and operating instructions should be retained for future reference. No object should bring weight to bear on to the AC power cords. POWER-CORD PROTECTION вЂ“ The AC power cords should be routed so that they are not likely to be walked on. IMPORTANT SAFETY INSTRUCTIONS READ INSTRUCTIONS вЂ“ All safety and operating instructions should be read before the subwoofer is operated. The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated вЂњdangerous voltageвЂќ within the productвЂ™s enclosure that may be of sufficient magnitude to constitute risk of electric shock to persons.

CAMBRIDGE SOUNDWORKS P500 MANUAL

в„ў P1000 and P500 Subwoofers User Manual В®

Cambridge soundworks p500