#Macsimizer mb1350 lock replacement install
#Macsimizer mb1350 lock replacement full
#Macsimizer mb1350 lock replacement free

If the concave edge of a board could collapse on the blade at the end of the cut, jamming the blade. If the board is warped, place the convex side against the fence. в– Place the workpiece flat on the miter table with one edge securely against the fence. W ARNING: To avoid serious personal injury, always keep your hands outside the no hands zone at least 3 in. Use the optional work clamp or a C-clamp to secure the workpiece when possible. OPERA TION в– Grasp the stock firmly with one hand and secure it against the fence. Rotate the miter lock handle approximately one-half turn to the left to loosen.

#Macsimizer mb1350 lock replacement full

6 2 0 OPERA TION в– Pull out the lock pin and lift saw arm to its full height.

#Macsimizer mb1350 lock replacement free

The workpiece must remain free on one side of the blade to prevent the blade from binding in workpiece. 6 2 0 CUTTING WITH YOUR COMPOUND MITER SAW W ARNING: When using a work clamp or C-clamp to secure your workpiece, clamp workpiece on one side of the blade only. The depth stop positions the blade (6.4 mm) 1/4 in.

It allows the blade to go below the miter table enough to maintain full cutting capacities. ADJUSTMENTS DEPTH STOP The depth stop limits the blade's downward travel. 6 2 22.5 ADJUSTMENTS SQUARING THE SAW BLADE TO THE FENCE See Figures 21 - 24 в– Unplug your saw. в– Raise saw arm to its full raised position. в– Push down on the saw arm and pull out the lock pin to release the saw arm. ADJUSTMENTS W ARNING : Failure to unplug your saw could result in accidental starting causing possible serious personal injury. Note: The blade bolt has left hand threads. The direction of blade rotation is also stamped with an arrow on the upper blade guard.

#Macsimizer mb1350 lock replacement install

ASSEMBL Y CAUTION: Always install the blade with the blade teeth and the arrow printed on the side of the blade pointing down at the front of the saw. Never use a blade that is too thick to allow outer blade washer to engage with the flats on the spindle. (254 mm) blade is the maximum blade capacity of your saw. ASSEMBL Y TO INSTALL BLADE See Figures 15 and 16. If you plan to use the stop block, slide the stop block on the back arm of the desired table extension first. 6 2 TABLE EXTENSIONS See Figures 11, 12, and 13. 6 2 ASSEMBL Y W ARNING: To prevent accidental starting that could cause possible serious personal injury, assemble all parts, make sure all adjustments are complete, and make sure all fasteners are secure before connecting saw to power supply. The 22-1/2 В° and 45 В° positive stops have been provided on both the left and right side of the miter table. 6 22.5 3 0 1 5 31.6 45 5 45 FEA TURES POSITIVE STOPS ON MITER TABLE Positive stops have been provided at 0 В°, 15 В°, 22-1/2 В°, 30 В°, and 45 В°. To transport, turn off and unplug your saw, then lower the saw arm and lock it in the down position. For convenience when carrying or transporting your miter saw from one place to another, a carrying handle has been provided on top of the saw arm as shown in figure 3. 2 LOWER BLADE GUARD DUST GUIDE UPPER BLADE GUARD SAW ARM MITER FENCE MITER TABLE MITER LOCK HANDLE BEVEL SCALE BEVEL LOCK KNOB. (254 mm) Saw Blade в– Miter Lock Handle в– Dust Bag в– Dust Guide в– Stop Block в– Small Wing Screw в– Clamp Brac. The following items are included with your Compound Miter Saw: в– 10 in. в– Examine all parts to make sure no breakage or damage has occurred during shipping. Hand pressure should remain on the saw arm to prevent sudden rise upon release of the tie wrap. UNP ACKING в– Lift the saw arm by the handle. Watch what you are doing and use common sense. SA VE THESE INSTRUCTIONS RULES FOR SAFE OPERA TION в– STAY ALERT AND EXERCISE CONTROL. в– NEVER reach to pick up a workpiece, a piece of scrap, or anything else that is in or near the cutting path of the blade.

в– NEVER hand hold a workpiece that is too small to be clamped. Learn the saw's applications and limita- tions as well as the specific potential hazards related to this tool. READ ALL INSTRUCTIONS в– KNOW YOUR POWER TOOL. The safety warnings do not by themselves eliminate any danger. The safety symbols, and the explanations with them, deserve your careful attention and understanding. RULES FOR SAFE OPERA TION The purpose of safety symbols is to attract your attention to possible dangers. TABLE OF CONTENTS в– Table of Contents, Introduction, and Product Specifications. Your new saw has been engineered and manufactured to Ryobi's high standards for dependability, ease of operation, and operator safety. (254 mm) Compound Miter Saw Model TS1350 - Double Insulated THANK YOU FOR BUYING A RYOBI COMPOUND MITER SAW.